[Communication Interface]：RS485
[Communication distance]：10km
[Operating Voltage]： DC 8-28V
[Installation Method]：DIN-Rail Mounting
[Size]：113*72*65mm
[Weight]：150 ± 5g
[Introduction]：The wireless intercommunication switch is a terminal device that uses LoRa modulation technology to achieve remote wireless switching value transmission. Operating in the 850.125-930.125 MHz frequency band, it supports four digital inputs (DIs) for data acquisition and four relay outputs (DOs) for control. Its core function is to enable remote synchronous control without the need for wiring, offering high ease of use and enabling quick integration into users' systems. It accepts an 8-28 V DC input and is coated with conformal coating, offering anti-mold, anti-humidity, and anti-salt spray properties.
Official Storec
| Pin | Device Port Description |
| 1 | Switch input port 1 |
| 2 | Switch input port 2 |
| 3 | Switch common terminal |
| 4 | Switch input port 3 |
| 5 | Switch input port 4 |
| 6 | Switch common terminal |
| 7 | GND |
| 8 | RS485-A |
| 9 | RS485-B |
| 10 | PE (protective earth) |
| 11 | DC 8～28V(V-) |
| 12 | DC 8～28V(V+) |
| 13 | Relay output normally open port 1 |
| 14 | Relay output COM port 1 |
| 15 | Relay output normally closed port 1 |
| 16 | Relay output normally open port 2 |
| 17 | Relay output COM port 2 |
| 18 | Relay output normally closed port 2 |
| 19 | Relay output normally open port 3 |
| 20 | Relay output COM port 3 |
| 21 | Relay output normally closed port 3 |
| 22 | Relay output normally open port 4 |
| 23 | Relay output COM port 4 |
| 24 | Relay output normally closed port 4 |
| 25 | STATE configuration reset button |
LED indicator and button description
| port | LED indicator color | illustrate |
| PWR | Blue LED | Power indicator light, always on when powered on, off when no power |
| LINK | Yellow LED | 1 to many (including 1 to 1) - bidirectional (when the devices have the same number of channels): |
| l As long as one slave is successfully connected to the master, the LINK indicator of the master will be on; | ||
| After the slave device is successfully connected to the host device, the LINK indicator of the slave device will be on; | ||
| 1 to many - two-way (different number of channels, each channel of the host is independently controlled by the slave): the host LINK indicator flashes several times according to the number of devices connected (cycle 300ms, after flashing, it goes out for 1s, and then flashes again). For example: if 3 devices are connected, the LINK indicator flashes 3 times according to the cycle, then goes out for 1s and flashes again; | ||
| STATE (indicator light) | Blue LED | Host: The indicator light is always on; |
| Slave: indicator light flashes slowly; | ||
| Pairing: indicator light flashes quickly; | ||
| Not paired: the indicator light is off; | ||
| STATE (button) | White buttons | 1. Press and hold for 2 seconds to enter pairing mode; |
| 2. Press and hold for more than 6 seconds to restore to factory settings; | ||
| 3. Press and hold to cycle through the pairing state and reset state; | ||
| 5. In pairing mode, short press to exit pairing mode | ||
| DI1-DI8 | Green LED | Device switch input data indication, normally on means there is input, normally closed means there is no input |
| DO1-DO8 | Red LED | Each of the 8 relay output switch indicators corresponds to the 8 relay outputs; normally on indicates output is in progress, and normally closed indicates no output. |