E180-Z8910SX Ebyte OEM/ODM Small size high reliability working in the 2.4GHz frequency band ZIGBEE module
[IC]：JN5189
[Frequency]：2405~2480MHz
[Power]：11dBm
[Distance]：0.5km
[Product weight]：0.9g±0.1g
[Size]：11.5*18mm
[Introduction]：E180-Z8910SX is a ZIGBEE3.0 module designed and produced by Chengdu Ebyte based on NXP JN5189 wireless SOC. It has a small size, low power consumption, high reliability, and works in the 2.4GHz frequency band. It has an ARM architecture, M4 core, and a clock frequency of up to 48MHZ.
Official Store
| No. | Pin Name | Pin direction | Application |
|---|---|---|---|
| 1 | NC | - | Reserved, directly suspended |
| 2 | GND | - | Ground wire, connected to the power reference ground |
| 3 | NC | - | Reserved, directly suspended |
| 4 | PD3(WAKE) | Input | The WAKE pin is mainly used to wake up the dormant terminal. It is high when it is powered on. When the pin is pulled low externally, the dormant terminal device will be awakened. |
| 5 | PIO8(TX) | Output | Serial transmission port TX |
| 6 | PIO9(RX) | Input | Serial receiving port RX |
| 7 | NC | - | Reserved, directly suspended |
| 8 | NC | - | Reserved, directly suspended |
| 9 | PIO2(MODE) | Input | Working mode switching pin, when the pull-down time is greater than 500ms, the working mode is switched. |
| 10 | PIO3(BAUD_R) | Input | The UART_BAUD_RESET pin is used to reset the baud rate of the device. It defaults to a high level after power-on. In any mode, the module serial port parameters will be restored to the default 115200 if the pin is pulled down for more than 1000ms. |
| 11 | PIO6(ACK) | Output | The ACK pin is used to indicate the status of the last user data transmission. The pin is pulled low before the transmission is started, and the pin is pulled high after the transmission is successful. |
| 12 | PIO7(GPIO0) | Input/output | GPIO input/output port 0 |
| 13 | VCC | - | Module power supply positive reference voltage, voltage range |
| 14 | GND | - | Ground wire, connected to the power reference ground |
| 15 | PIO10(GPIO1) | Input/output | GPIO input/output port 1 |
| 16 | PIO4 | - | Reserved, directly suspended |
| 17 | PIO5 | - | (PIO5 pulled low, the module is in download mode; PIO5 pulled high, the module is in running mode) |
| 18 | PIO16(AUX) | Output | The AUX pin indicates the current working status of the device. When the pin is low, it indicates that the device is busy, and the high level indicates that the device is idle. |
| 19 | PIO11(GPIO2) | - | Reserved, directly suspended |
| 20 | NC | - | Reserved, directly suspended |
| 21 | PIO14(ADC1) | Input | ADC detection port 1 |
| 22 | PIO15(ADC2) | Input | ADC detection port 2 |
| 23 | NC | - | Reserved, directly suspended |
| 24 | NC | - | Reserved, directly suspended |
| 25 | SWCLK | - | Reserved, directly suspended |
| 26 | SWDIO | - | Reserved |
| 27 | PIO17(PWM3) | Output | PWM output port 3 |
| 28 | PIO18(PWM2) | Output | PWM output port 2 |
| 29 | PIO19(PWM1) | Output | PWM output port 1 |
| 30 | PIO21(LINK) | Output | The LINK pin indicates the current network status of the module, and the output high-level meter has been added to the network |
| 31 | PIO20(PWM0) | Output | PWM output port 0 |
| 32 | NC | - | Reserved, directly suspended |
| 33 | NC | - | Reserved, directly suspended |
| 34 | NC | - | Reserved, directly suspended |
| 35 | NC | - | Reserved, directly suspended |
| 36 | GND | Input/output | Ground wire, connected to the power reference ground |
| 37 | RESET | Output | Reset pin |